STANDARD DECAL INSTALLATION

For optimum results, surface temperature should be above 50�F and below 90�F.
If necessary, move vehicle to a location where the temperature can be within the
installation guidelines.
Application Procedures:
You can choose to apply vinyl in one of two ways; dry or wet. Applying vinyl dry does not allow for any mistakes, and recommended for small decals. Once the vinyl touches the surface, there is no removal without damage. We suggest that all customers use the wet process for larger graphics.
Do Not use the wet method on Wall Vinyl or reflective vinyl.


MATERIALS NEEDED:
�ruler �masking tape �scissors
�lint free cloth �surface cleaner(isopropyl alcohol is recommended)
��Slip� Solution (is optional for larger graphics).
STEP 1:
After determining the location for your graphic, clean the surface with a lint free cloth and cleaner solution. Be sure to turn the cloth several times to insure thorough cleaning and wax removal. After doing this you should get a "squeaky" sensation when lightly dragging your fingers across the surface.
STEP 2:
Using small strips of masking tape, locate the graphic where it is to be installed. If the graphic has a horizontal edge or reference point, you can use this for measuring the location from a body line or trim molding. If the decal has a flowing design, you'll have to step back and visually inspect its location to determine if that is where you want it. Once this is done, make measurements from individual points on the design and transfer the locations to the opposite side of your vehicle. ( This is the step you need to take your time on, measure from different locations, once the graphic is installed, it cannot be moved).
STEP 3:
Place two strips of masking tape (slightly overlapping each other) vertically in the approximate center of the graphic. This is known as the "hinge" method. This will allow you to install half of
your decal at a time.
STEP 4:
Remove the masking tape strips from one end of the decal and slowly peel the backing paper away, taking care not to touch the adhesive side of the graphic. Use scissors to remove the backing paper and discard.
STEP 5: WET APPLICATION (Large Graphics mostly)
Spray the surface where the backing paper has been removed with a "slip" solution. Do this on the vehicle surface as well. Slowly swing the exposed part of the decal onto the wet surface, keeping only enough tension on it to avoid wrinkles. As the decal meets the surface, squeegee from center to ends using semi circular, overlapping motions to push the air from underneath. There is no need to use excessive pressure because the slip solution serves as a lubricant for the air to be pushed outward.This will need to dry for possibly 2 hours or more before the mask can e removed.
STEP 5: DRY APPLICATION (Small Decals)
Slowly swing the exposed part of the decal on to the surface, keeping only enough tension on it to avoid wrinkles. As the decal meets the surface, squeegee from center to ends using semi circular, overlapping motions to push the air from underneath. Use moderate pressure to insure good adhesion.

STEP 6:
Slowly remove the center hinge and very carefully peel the remaining backing paper away. Just as before, swing the decal over and squeegee it down using the same motions described above. Resqueegee the entire surface of the graphic again to insure all areas have adhered.
STEP 7:
Remove the application tape by pulling it back at a 180� angle. Make sure to watch the decal to make sure it's not lifting from the surface. If the graphic seems to be lifting, gently push the application tape back in the opposite direction that you were removing it and re-squeegee that area. NOTE: If too much detergent is used in the slip solution, or surface temperature is cold, you may have to wait for several minutes to allow drying time before removing the application tape.
STEP 8:
Once the decal is installed and the application tape removed, carefully inspect the area for bubbles. In the case of very small air bubbles, usually they will pass through the vinyl within a couple weeks. Larger bubbles may need to be removed, puncturing them with a pin or needle at the edge and softly pushing the air out towards the puncture.

Wet Application Fluid:
You can make you own application fluid with 4 drops of dishwashing liquid (dawn, joy, or baby shampoo etc.) to 1 quart of water in a spray bottle. We use Windex without ammonia in our shop.

Problems or Questions: Call 608-387-5464 or e-mail: RBeans@mcbeansdecals.com

For an excellant video on installation we recomend the following: https://www.youtube.com/watch?v=6ZvahnkLJOM. Just copy and paste this to your browser
aaaaaaaaaaaaiii